
You’ve had the survey, the quote has arrived, and you’re reading it at the kitchen table with a cup of tea. Most of it makes sense: the styles, the colours, the number of windows. Then there’s a line that says something like “Uw 0.75 W/m²K”, and you’re left wondering whether that’s good, bad or just there to fill space.
That number is the U-value, and it’s the single most useful figure for comparing how well windows and doors keep your home warm. Once you know how to read it, you’ll know exactly what you’re paying for.
What is a U-value?
A U-value measures how quickly heat escapes through a part of a building, such as a window, a door or a wall. The lower the number, the less heat gets out, and the better that part of the house insulates.
It’s measured in watts per square metre per degree, written W/m²K. In plain terms, it tells you how many watts of heat pass through each square metre for every degree of difference between the temperature inside and outside. A window with a U-value of 1.0 lets through half as much heat as one with a U-value of 2.0.
What does that look like in real life?

Take a typical window of about 1.5 square metres on a winter evening, with the room at 20°C and 5°C outside. That’s a 15-degree difference, and the heat escaping through the window works out roughly like this:
| Window | U-value (W/m²K) | Heat escaping |
|---|---|---|
| Old single glazing | About 5.0 | About 112 watts |
| Building regulations benchmark | 1.4 | About 32 watts |
| High-performance triple glazing | 0.75 | About 17 watts |
For that one window, the single glazing is losing as much heat as an old-fashioned 100-watt light bulb gives off, for as long as the heating is on. Multiply that across every window in the house, over every winter evening, and you can see why the U-value matters.
What’s a good U-value for windows in Ireland?

These are the figures worth knowing:
- About 5.0: typical single glazing.
- 1.4: the benchmark in Ireland’s building regulations (Technical Guidance Document L) for windows, doors and rooflights in new homes. It’s also the maximum allowed under SEAI’s windows and doors grant.
- 0.80: the Passive House window target for a climate like Ireland’s, the most demanding energy standard for homes. Meeting it takes certified windows in a house designed to the standard, but it’s a useful reference point. Our post on passive house and high-performance windows explains more.
Anything at or below 1.4 meets the regulations and the grant requirement. The lower you go below that, the less heat you lose. For reference, here are Fairco’s figures:
| Product | Double glazed | Triple glazed |
|---|---|---|
| Performance uPVC windows | 1.2 | As low as 0.75 |
| OMNIA Flush windows | 1.2 | As low as 0.75 |
| Aluminium windows | 1.4 | As low as 1.0 |
| OMNIA Flush doors | 1.2 | As low as 0.82 |
| Apeer70 composite doors | n/a | 0.85 (triple glazed as standard) |
| Aluminium doors | 1.4 | 1.1 |
Whole-window and centre-pane U-values

This is the part that catches people out. A window’s U-value can be given in different ways:
- Ug is the glass alone, measured at the centre of the pane.
- Uf is the frame alone.
- Uw is the whole window: glass, frame and the edge where they meet.
The centre of the glass is usually the best-performing part of a window, so a centre-pane figure will look better than the window really is. When you compare quotes, make sure you’re comparing whole-window (Uw) figures. It’s the only fair comparison, and it’s the figure the building regulations and the SEAI grant use.
What affects a window’s U-value?
Several parts of the window work together to set the final figure:
- The number of panes: triple glazing adds a second insulating gap.
- The gas between the panes: argon, which is heavier than air, slows heat moving across the gap.
- Low-E coatings: an invisible layer on the glass that reflects heat back into the room.
- The spacer bar: warm-edge spacers can improve the whole-window U-value by between 5% and 18% compared with aluminium spacers. See what is a warm-edge spacer bar.
- The frame: the chambers inside a uPVC frame, or the thermal break in an aluminium one.
The window buying guide explains each of these in more detail, and double glazing vs triple glazing helps you decide which suits your home.
U-values, your BER and the SEAI grant
New windows and doors with lower U-values can improve your home’s Building Energy Rating, which is covered in understanding your BER. To qualify for SEAI’s windows and doors grant, the new windows and doors must have a U-value of 1.4 W/m²K or lower, and the home has to meet SEAI’s other conditions, including its age and insulation levels. Fairco is an SEAI-registered contractor, and the grant page explains how it works.
Does a lower U-value always mean a warmer home?

A lower U-value means less heat escaping through the window itself, but it isn’t the whole story. A well-rated window fitted with gaps around the frame will still let heat out, which is why installation matters as much as the figure on the quote. Read understanding thermal bridging for more on where the frame meets the wall.
The rest of the house matters too. SEAI estimates that a home can lose up to 10% of its heat through poorly performing windows and doors, and up to 30% through poorly insulated attics and walls. New windows make the biggest difference in a home that’s already well insulated, or as part of a wider upgrade. For the running-cost side, see why energy-efficient windows and doors make financial sense.
Ask for the numbers
Whoever you buy from, ask for the whole-window U-value of every window and door on your quote. At Fairco, your surveyor will confirm the figure for your order, and you can compare glazing options side by side at the Santry or Deansgrange showroom. Or book a free consultation, and a Fairco surveyor will come to your home and talk you through the options.

